DPL Machine

It is a more advanced method of IPL that uses the light at a controlled intensity over the root of the hair to be removed or the hair follicles. The hair root absorbs the light, which is then converted into heat energy and used to destroy the pigments. Besides, the effective contact cooling technology on the handpiece provides the best comfort for clients.

Apart from both body and facial hair removal, it's often suitable for facial rejuvenation treatments to target acne, uneven pigmentation, and enlarged pores. It cleanses your pores, improves blood circulation, and even tightens and lifts aging skin. Compared with traditional photo rejuvenation, it has higher selectivity, more precision, and more efficiency. In treatment effect, effective time, safety, and technical aspects have been upgraded in four major aspects.

● For hair removal treatments, other systems use the 640-1200nm wavelengths. However, the hair follicle does not need such a broad light spectrum. We use the professional 640-750nm wavelength. The precise wavelength will not only improve results, it will also reduce the level of pain during the treatment.

● The DPL handpiece delivers light energy that gradually heats the skin by pulse stacking or a sliding technique until the ideal amount of energy is delivered to the hair root. This new technology heats the follicle gently and for longer-lasting results. This means the hair germ cells are directly targeted and permanently damaged in the active growth stage.

● Hair follicles are not damaged by a single high-energy pulse as in laser or IPL but by repetitive application of low-energy pulses that raise the temperature of the dermis gradually and for longer. Most people say it just feels like a pleasant warm massage.

● DPL has the ability to clean the pores and tightens the skin if it is aged, it uses tender pulses of energy at a relatively higher repeated rate. This makes the skin gets heated gently. The slow build of energy helps in making the procedure more comfortable and keeping skin trauma at a minimum. It combines low fluence laser pulses with contact cooling to make the experience comfortable.

● For IPL, it can be used only on specific skin tones and hair colors and cannot be used for dark skins, red, white and gray coloured hairs. While DPL is suitable for all hair and skin types and safe for all skin colors, whether it is coarse and dark hair or fine and light ones.

With DPL, you can maintain permanent hair reduction. This is due to the fact that hairs grow in cycles and only those in their active growth phase will be treated with this method; however, some may regrow but should appear thinner and lighter than before.
It is essential to remember that not all hair types and skin tones will benefit from DPL treatment. The best candidates for positive results are dark, coarse hairs. On the other hand, those with lighter or thinner hairs may not experience much success with this method of hair removal. Additionally, individuals with very light or very dark skin tone should be wary as the light energy used can also affect their complexion during treatments.

Narrow Spectrum Light (DPL) refers to a new type of optical skin rejuvenation technology with a spectral range of 500~600nm or 550~650nm. Different from the traditional photon skin rejuvenation technology (IPL, Intense Pulse Light), the narrow-spectrum light technology can excite a selected narrow-spectrum pulse light in the 100nm band. This band also includes the absorption peaks of melanin, oxygen and hemoglobin. The effective therapeutic energy can be precisely concentrated, and the problems of facial pigmentation and telangiectasia (red face syndrome) can be solved quickly and efficiently. DPL narrow-spectrum light skin rejuvenation is known as an epoch-making optical cosmetic skin rejuvenation technology because of its curative effect significantly surpassing photon skin rejuvenation, and the treatment cycle is significantly shortened.

Scope of application of DPL machine
● Remove or dilute facial pigment spots

● Remove or improve facial redness
(Red blood streaks on the skin are caused by skin thinning, discoloration, exposure of capillaries and veins, etc. Photons of specific wavelengths of photons can make the tiny blood vessels on the surface of the skin absorb energy to the maximum within a certain period of time, resulting in tiny blood vessels. Blood vessels coagulate or subside without damaging the skin, while stimulating the growth of collagen in the dermis of the skin, increasing the thickness and density of the epidermis, so that small blood vessels are no longer exposed, and the elasticity and resistance of the skin are significantly increased)

● Treat facial acne and fade acne marks
(The photothermal effect will promote the opening of the pores, allowing more oxygen to enter the pores, restricting or killing the Proteobacterium acnes, and has no effect on the surrounding normal skin tissue, helping the inflammatory acne to subside, and there is a brightening effect when the pores shrink. The role of the skin to eliminate or lighten the marks or scars left by acne)

● Improve rough skin and dilute fine wrinkles
The principle of DPL hair removal: After the melanin in the hair shaft selectively absorbs light energy, the light energy is converted into heat energy, and the heat is transmitted through the hair shaft to the isthmus of the hair follicle and the prominence of the hair follicle (hair papilla, hair growth point) to destroy the hair papilla. The blood vessels are heated and shrink, so as to achieve the effect of hair removal.

First of all, as the DPL machine is a high-precision electronic machine, it should not be placed in a wet, exposed to direct sunlight, inflammable or explosive materials place to prevent damage caused by environmental factors.

Secondly, cleaning, the surface of the DPL machine must be kept as clean as possible. It is suggested to cover it with flannel or gauze when not in use to prevent the malfunction of the button due to dust accumulation.

In addition, when cleaning, do not rinse the machine body directly with water. Be sure to wipe it with a soft, damp cloth. The water on the rag should not be too much. After all, as the DPL machine is an energizing device, it is easy to burn if water comes in it. (Here you can also use a rag to rub alcohol, but not too much alcohol, alcohol is easy to volatilize, not easy to remain on the surface of the instrument, but some instruments should not be wiped with alcohol, it is easy to corrode.)

For those spare parts, they must be cleaned each time after do one treatment. When cleaning, use a dry rag or a wrung out wet cloth to wipe. Do not wash. Do not contact with oily or corrosive cosmetics.

Some DPL machine need to add water for heat dissipation. All DPL machine that need to add water, please be sure to add pure water or distilled water, and change it at least one and a half months, so that the internal water of the instrument is clean, no impurities. The
DPL machine dissipate heat through the water circulation, when the water is not clean, affecting the water flow, then heat dissipation, so the machine is prone to failure. (When the machine is not used for a long time, the water inside the machine should be drained.)

The correct way of operation is very important for the maintenance of the DPL machine, so you must pay attention to some details during using them.

When using these DPL machine, you should not keep long fingernails, and do not press the buttons on the device too casually, because many machine panels now use soft buttons, it is delicate . If the nails are too long or randomly pressed, it will easily lead to cracking, which will easily shorten the life of the screen on the DPL machine. The machine body cannot be beaten, strong collision, etc. All wire-type fittings are strictly prohibited from being pulled and entangled to prevent the power cord breaking.

Finally, if the machine is not used for a long time, you should use a moisture-proof and dust-proof bag to protect the DPL machine as a whole. At the same time, it is best to turn it on for about one hour every half month or so to avoid the internal electronic components being damp.