DPL machine installation and specific operation

1. First of all, we unpack the package and install the hanger and handle (the handle must be in place, if it is not in place, the handle will burn)

2. Next, add water to the machine. Note that the machine must be filled with water before it can be turned on. When adding water, we get the water filling funnel, screw the water filling funnel to the end of the water filling hole, and unscrew the cover of the overflow hole at the same time.

3. Start to add water, pay attention to only add two kinds of water; pure water or distilled water, can not add tap water and mineral water, water quality impurities will affect the luminous body and reduce the life of the light source.

4. Fill up the water until the water flows out from the overflow port, indicating that the water is full. Note that the machine needs to change the water once a month. The summer weather is hot, and a little water can be added a week.

Power on: 

Turn on the key, turn it to the right, and there is an emergency switch next to it, which is usually not used.

Screen explanation: 

Enter DPLmachine, let's explain hair removal first

hair removal mode

Normal mode hair removal: no fast flash, only one click to emit light, suitable for small parts of hair like; lip hair, underarms, hairline, bikini, etc.

Fast hair removal mode: it is a fast hair removal mode, which can emit light continuously, and is suitable for large areas of hair, such as hand hair and leg hair, and can adjust the frequency of the light

About Pulse

1. Pulse is a concept of time

2. Pulse width: the high one is the flashing time

3. Pulse interval: the low one is the dwell time without flashing

4. Why do you set so many pulse times, because a long pulse will make the epidermis and 5. The target tissue you want to destroy heat up rapidly at the same time.

6. The pulse interval can stop the energy injection while using sapphire to quickly cool down the skin.

Pulse recommended settings

Hair removal: the short-term energy injection is not enough to cause it to damage the dermal papilla and the effect is not good (the pulse width and pulse interval time values of hair removal are relatively high)

The pulse width time is long, and the pulse interval time is also long (in a relatively long pulse width time, there must be a long enough skin cooling time, so the pulse interval time should also be longer)

Energy: starting from 3-5, there is no feeling that it is increasing, the energy of hair removal is the key.

Principles of parameter adjustment:

The energy of light will give people three feelings

One is slightly hot, the other is with acupuncture, and the other is hot

Slight heat means that the energy is low and there is a strong needling sensation.

The skin is acceptable

If it feels hot, it means that the energy is high, you can lower it appropriately

hair removal tips

1. The hair is long and black; you can ask the customer to shave it three days in advance, or you can cut it as short as one millimeter at that time, and absorb light through the black stubble, and conduct heat to the root of the hair. The white and tender fluff can be done directly without shaving, and some hairs will fall off automatically after a week.

2. When operating, try to increase the energy as much as possible until the customer has a strong needling sensation and it is acceptable.

3. Walk six times as a whole, 4-6 times for coarse hair, and 6-7 times for fine hair

4. Insist on completing the course of treatment according to the interval cycle! Because the hair follicle recovery period is 21 days, and the hair growth cycle is about 28 days, all intervals are 21 to 28 days, and try not to exceed 30 days.

Pulse recommended settings

Skin rejuvenation: pulse width 3-5 pulse interval 10-25ms

Energy: starting at 3-5, I don’t feel like it’s going up

Parameter setting principles:

1. If the skin is thick, dark yellow and rough, you can increase the pulse width and increase the energy density at the same time

2. If the skin is dark, the epidermis is thicker, and the pigmentation is pigmented, the pulse interval can be increased

3. If the skin is darker, the epidermis is thinner, and the skin is sensitive, the energy density can be set smaller

4. If treating parts with less subcutaneous tissue, the energy density can be appropriately reduced

5. As the number of operations increases, the energy density can be appropriately increased

6. The reaction is not obvious, the customer can tolerate it, and the energy density increases

Photon skin rejuvenation operation process:

1. Cleanse your face with makeup remover and wear an eye mask

2. Apply the cold gel and choose the appropriate energy parameters

3. Burning and prickling sensations are clinical standards

4. Each spot has a 1 mm spot overlap

5. Apply cold compress for 15-30 minutes after operation

6. Cold compresses eliminate subsequent heat and disperse heat to avoid burns

Operating time and interval

Each operation takes about 20 minutes. In order to achieve the best operation effect, it is recommended to operate about 5 times for each course of treatment. The interval between each operation is about 20 days. A course of treatment usually takes more than four months.